Category Archives: news

Updates on Kill-Switch (E-Vehichle for son).

During my latest testing phase, there was an accident with the motor controller.  This has put a small speed bump in my little project.

However, this may be a blessing in disguise.  I wanted to put in my own motor controller before, but I was trying to do this build without purchasing much.  So, I was using the built-in controller within the old hover board housing.  This came with many obstacles; for one, the circuit was very sensitive to change.  If I wanted it to work; the LEDs and everything had to be perfect. Otherwise it would throw errors. Keeping in mind that I do not have any manual, documentation, etc on the hardware here.

Once I replace their motor controller with mine, it will be even better for my automation.  I actually do have RPI motor controller HATs; however nothing rated for 500w.  So I am going to be using the following per side. http://a.co/eHzWM2i

This will allow me to control the speed with the battery, and hub motors I already have. Just add a potentiometer per side, and were in business. Those pots will be controlled via very small servo.  This will allow the user to control them, but the servos will put them back to zero (stop) after use.  This also enables the control via RPI3, as I mentioned before.

On another note; I am considering using casters in the front since you will be able to steer via the controls.  Alternatively, I get one controller and use it as a throttle only.  This would work, but then I would have to have front steering.

 

Thanks for all the support,

Matt Curry

DIY Eclipse Glasses

Nothing Fancy here, but they work. (Use are your own risk)

First off, never look directly into the sun!  Always have the PROPER eye protection!

Supplies
1. Pen
2. Paper
3. Cereal box
4. Aluminum foil
5. Scissors

Yes, that’s it!

How to make an eclipse viewer yourself:
1. Put the cereal box on the piece of paper and trace the outline of the bottom of the box, creating a rectangle.
2. Cut out the rectangle.
3. Take two pieces of tape and make loops, then place them on both ends of the rectangle.
4. Take the piece of paper and place it inside the bottom of the cereal box tape-side down.
5. Close the cereal box up once the piece of paper is inside.
6. Create two holes in the top of the box, one on each side.
7. Cut the holes out with scissors — one will be for your eye, and the other will be covered by foil.
8. Tape the top of the box down revealing the two holes.

9. Take a piece of aluminum foil and cover one of the holes up (it doesn’t matter which one you choose.)
10. Take your pen, make a tiny hole in the middle of the aluminum foil.

And you’re done!

Got an Idea? Need Help? Raspberry PI prototyping!

Just another thing that I helping with lately.  If anyone need help with a new idea for a Raspberry PI, or IoT device message me.  I have been  through several POC’s (proof of concepts).

Keep in mind, if you are working on a new product; or sensitive information I keep all client info secret, and have no issues with an NDA.

  • Home Automation
  • Voice Recognition
  • Several TTS/STT Options
  • Custom Hardware
    • Integration with existing hardware
  • Custom Software
    • Custom Plugins/Adjustments
    • Coding
  • R&D on Subject Matter
    • Build
    • Test
    • Design
  • … and whatever else is needed …

Happy to just answer questions; or see what I can do to help.  Just contact me.

Don’t forget! Linux Learning Resources

This is kept under the Linux Learning Project and Learning Resources section of the site, and is updated occasionally with new links.  Feel free to suggest one by contacting me directly.

LEARNING RESOURCES

Help/Chat:

Resources:

Need DevOps Help?

  • Had issues with your DevOps pipeline?
  • Need help streamlining automation or configuration management?
  • Need to green field or “lift and shift” applications into the cloud?

If you are trying to do any of these, and running into issues please contact me.  I am now open to consulting directly.  Fixing even a few small inefficiencies can have a huge impact on the bottom line.  Not only that, if the DevOps philosophies are really taken up, its likely that the employee base will also be happier, and proud of their accomplishments as a team.

As far as technologies I support, please take a look at my Technologies page.  (Updated often)  I am also happy to take on new ones for a project if needed.

Creating an efficient pipeline is what I do; and a fully functional system that is working well can be an amazing thing.

 

Matthew Curry
MattCurry.Com

 

The Eagle Has landed….

All,

I have made it…. the move is complete!   I just wanted to say thank you for everyone that has been waiting on me.  I know I have taken a while on a few things, and I am finally in a position to run with everything again.  I finally have a decent internet connection [330mbps/330mbps]; so I will also be able to host things at high speed for us now as well.

As far as the installer goes, I hope to be done very soon with it ;  I am putting my final touches on it for the Pixel desktop.  If I get time I might be able to get Bluetooth working!  However, I have to get caught up first.

For those waiting on hardware, most has been shipped with a few exceptions.  I have notified those people.  I have a true ‘shop’ area again, and this will allow me to be much more efficient.  Meaning shorter wait times/etc…

 

Sincerely,

-M

Thank you to all… Jasper v1.6 Image News!

First, I would like to say thank you to the community members for helping out. I have gotten a lot of input on the new image.  This has also given me better feel for what the community wanted in an image. Which leads me to the next bit of news.

Some of you are undoubtedly wondering why I have not released my Jasper v1.6 image as of yet.  Well, I can assure you there are very good reasons.

Firstly,  I have had some severe family/health issues come up as of late which take priority.  I am also in the middle of moving a family of 5.  Combine that with the other reasons below, and I feel that most will feel the wait to be worth it.

This leads me to the next bit of news, however shocking it may be.

  1.  There will be no version 1.6 image.
    1. There will be no image at all…
  2.  Instead, there will be a full installer.
    1. This is one of the reasons for the delay.
  3.   The installer will work with a full GUI, and on the desktop.
    1. Examples:
      1. Full ubuntu Install.
      2. Fresh RPI install with GUI.
  4. The installer will be iterated on by feature going forward.
    1. We can add community approved features one at a time.
      1. Example:
        1. Change Jaspers Name
        2. Change STT after setup
        3. Etc.

FAQ (COMING SOON)

  • So whats that mean for me?
  • What do I do if I am running Jasper v.15?
  • Where do I get the installer?
  • Do I need to upgrade?

 

Jasper Kits on hold…

These were for the community, and I have enjoyed designing and building these kits.  However, I am at a point now, where I do not have the time to properly maintain and build and ship them.  This is not necessarily a permanent decision, I may bring them back in the future given I have the time.

That being said, I do have a few left.  If you are interested please let me know now.  I will get an exact count soon, and update it here.  Once they are gone, I will not be building more.

With all that being said, I am still here to help with questions.  I am also still developing what I hope is a better user experience with my images.  (Version 1.6 out soon!)

If you have any questions; or would like one of the last kits, I would suggest speaking up now.  Not that I will disappear, but I will be unable to spend the time on them for a while starting soon.

I also wanted to say thank you again to the community members that are helping each other, and the new guys.  I do notice, and it is appreciated.

-M

Jasper Image V1.6 – Release Date!

I have recently had a large number of people wanting to know the exact release date for the v1.6 image. I will release it without the installer, and release the installer separately so it can be used on images that are not mine.

  • Release Date:
    February 15, 2017

I would highly suggest that if there is annoyance; or fix for the next release that it be reported ASAP to the room in our SLACK.

 

Thanks for your patience,

Matthew Curry